Skip to main content

HENGYI BURNERS

Infrared burner bank above a conveyor in a powder coating oven, titled Infrared Burners for Powder Coating Ovens

Infrared Burner for Powder Coating Oven

An infrared burner for a powder coating oven heats the coated part directly, so the powder melts, flows and starts to cure faster than with hot air alone. Hengyi Burners makes gas-fired ceramic infrared burners for powder coating ovens, booster zones and gel stations, in LPG and natural gas versions. This page helps you choose a burner and tells you what to send us for a quote.

Why Use an Infrared Burner for a Powder Coating Oven

First, a convection oven has to heat the air, the oven walls and the part before the powder can cure. In contrast, infrared radiation heats the surface of the part straight away. As a result, coaters use infrared to:

  • For example, gel the powder quickly before parts enter a convection oven.
  • Also, shorten the line, or run it faster, in a limited floor space.
  • Moreover, cure flat or simple parts with little or no convection stage.
  • Finally, cut idle gas use, because infrared burners reach working heat in minutes.
Infrared burner for powder coating oven: cure stages and time to reach cure temperature for convection, hybrid and infrared ovens

For the full process, read our guide on how infrared burners improve powder coating curing.

Our Infrared Burners for Powder Coating Ovens

ModelSize (L × W × H)Best for
HY-2602936 × 135 × 245 mmLong oven zones and large panels
HY-2002750 × 130 × 250 mmMedium ovens and coating lines
HY-802See product pagePowder coating ovens and industrial heating
HY-1602570 × 130 mmSmall batch ovens and drying

All four models run on LPG or natural gas. For example, the HY-2602 reaches a surface temperature of 800 °C and above at a standard gas pressure of 280 ± 50 mmH₂O. In addition, each burner can be paired with our ignition needles and ignition controllers.

How to Choose an Infrared Burner for Your Powder Coating Oven

1. Size the Heated Zone

To begin, start with the height and length of the parts that pass the burners. Then choose a model length and the number of burners that cover that face evenly.

2. Work Out the Heat Load

Next, consider part weight, line speed and the cure temperature from your powder maker. Our guide on infrared burner size for industrial ovens covers the three common sizing methods.

Comparison of load calculation, empirical testing and manufacturer sizing for powder coating oven infrared burners

3. Match the Fuel and Pressure

After that, tell us whether the oven runs on LPG or natural gas, and the supply pressure at the burner. As a result, we fit the right nozzle before shipping.

4. Test the Heat Spread

Finally, run a thermocouple test on real parts after installation. Then, if one area runs hot or cold, adjust the burner spacing or angle.

Installation and Safety Tips

  • First, keep powder overspray away from the burner face, because dust blocks the ceramic pores.
  • Also, make sure the oven has enough exhaust and fresh air for combustion.
  • In addition, use flame monitoring and a safety shut-off valve on every burner bank.
  • Finally, have gas connections made by a licensed gas fitter, following local codes such as NFPA 54.

For upkeep, see how to maintain an industrial infrared gas burner.

FAQ: Infrared Burners for Powder Coating Ovens

Can infrared burners fully cure powder coating?

For flat or simple parts, yes. However, complex or heavy parts usually cure best with infrared for gelling plus a convection stage to finish.

Can I add infrared burners to my existing oven?

Often, yes. For example, many coaters add an infrared booster zone at the oven entrance. Send us the oven size and line speed, and we will suggest a layout.

Which is better for powder coating, LPG or natural gas?

Both work well. In practice, the choice usually depends on what fuel your site already has. Read natural gas vs LPG infrared burners for the differences.

How much gas will the burners use?

It depends on burner input and hours of use. Our guide shows how to calculate infrared burner gas consumption with a worked example.

Get a Quote for Your Powder Coating Oven

To get the right infrared burner for a powder coating oven, send us your oven size, part size, line speed, fuel type and supply pressure. Then Hengyi Burners will recommend the right infrared burners and send a factory price. Contact us or browse all infrared gas burners.